Basic Installation Guide for New Water Softener Fleck 24 volt AC transformer - Which to Choose Sediment filter ahead of the softener - When, Why, and Which one. Elan Water Care Water Softener UE-89 HANKSCRAFT H2O PRODUCTS and Replacement Valves Valve Replacements - Fleck 8500 / Twinflo 100E with Fleck 9100 or a single valve / tank. Plus the backwashing requirements of the water softener. Consult your dealer for alternative instructions if the pumping rate is insufficient. (3) Remember that the water softener INLET is attached to the pipe that supplies water (i.e., runs to the pump), and the OUTLET is the line that runs toward the water heater.
Written by Megan Mattingly-Arthur; Updated July 21, 2017
Tip
Press and hold the 'Regen' button for three seconds to initiate an immediate manual regeneration. Setting instructions may vary by water softener model. Contact Cuno customer service to obtain model-specific setting instructions for your MacClean water softener.
MacCLEAN's water softening systems help to remove minerals such as calcium and magnesium from your water, reducing the occurrence of inconveniences like soap scum and hard water spots. Programming the various settings for a MacCLEAN water softener is a simple process. For best results, refer to your water test data sheet throughout the setting process. A subsidiary of 3M's Cuno Incorporated division, MacCLEAN has been producing residential water treatment and water softening systems since 1934.
Press the 'Clock Set' button on the water softener control panel; a digital clock appears on the display screen and the hours digits begin to flash. Use the 'Up' and 'Down' arrow buttons to adjust the hours place digits as desired; press 'Next' to advance the flashing to the minutes place digits. Use the same process to set the minutes digits; press 'Next' to save your changes and exit the clock setting mode.
Manual configure wifi connect mac. Press and hold the 'Next' and 'Up' arrow buttons simultaneously for three seconds to access the programming mode; 'Hardness: 20' appears on display screen. Press the 'Up' and 'Down' arrow buttons to adjust the hardness from '20' to the desired value. Set the amount of hardness in grains of hardness as calcium carbonate per gallon; refer to your water test data sheet when setting the grains of hardness. Press the 'Next' button.
Use the 'Up and 'Down' arrow buttons to adjust the indicator to specify the maximum number of days between regenerations; the maximum days between regeneration is 28. Note the 'Regen Day' message and indicator on the digital display. Press 'Next.'
Use the 'Up' or 'Down' buttons to adjust the regeneration time hour as desired; press 'Next.' The default regeneration time is 2:00 a.m. Use the same process to set the minutes for the regeneration time. Press 'Next' again to exit the water softener programming mode.
References (1)
About the Author
Megan Mattingly-Arthur has been writing professionally since 1998. She has contributed to various publications, including 'Teen Voices' and 'Positive Teens' magazines, as well as a book, 'The Young Writer's Guide to Getting Published.' Mattingly-Arthur is studying travel and tourism through Penn Foster Career School.
Cite this Article
Choose Citation Style
Macclean Water Softener Manual Model Cs1000
Mattingly-Arthur, Megan. 'How to Set a MacClean Softener.' Home Guides | SF Gate, http://homeguides.sfgate.com/how-to-set-a-macclean-softener-13409350.html. 21 July 2017.
Mattingly-Arthur, Megan. (2017, July 21). How to Set a MacClean Softener. Home Guides | SF Gate. Retrieved from http://homeguides.sfgate.com/how-to-set-a-macclean-softener-13409350.html
Mattingly-Arthur, Megan. 'How to Set a MacClean Softener' last modified July 21, 2017. http://homeguides.sfgate.com/how-to-set-a-macclean-softener-13409350.html
Note: Depending on which text editor you're pasting into, you might have to add the italics to the site name.